piaggio zip sp 50 2t lc <-2000

Crankcase MODIFICATIONS: BORING AND CHAMFERING - To be combined EXCLUSIVELY with crankshafts 53 9212 - 5316005

IT IS ADVISED TO USE crankshaft 53 7600

Crankcase MODIFICATIONS: BORING AND CHAMFERING - To be combined EXCLUSIVELY with crankshafts 53 9212 - 5316005 (53 9703 - 5314544 - 5314887)

Crankcase MODIFICATIONS: BORING AND CHAMFERING - To be combined EXCLUSIVELY with crankshafts 5313270 (and 5316029 AFTER FITTING SPACER 0716345)

Crankcase MODIFICATIONS: BORING AND CHAMFERING - To be combined EXCLUSIVELY with crankshafts 5316029

for CRANKSHAFTS 53 9212 - 5316005 (53 9703 - 5314544 - 5314887)

to be assembled EXCLUSIVELY with Malossi MHR C-one ENGINE CRANKCASE 5715844

to be assembled EXCLUSIVELY with: ENGINE CRANKCASE 5715845 AND CRANKSHAFT (stroke 44 mm) 5316029

Crankcase MODIFICATIONS: BORING AND CHAMFERING - To be combined EXCLUSIVELY with crankshafts 5316005 (53 9703 - 5314544 - 5314887)

Spare part for Malossi CRANKSHAFTS 53 9703 - 5313270 : out of production

TO COUPLE ONLY WITH cylinder Kits 31 8884 - 3112099.T0 - 3113030 - 3115142.T0 - 3115349 - (31 9128 - 3112099 - 3115142 : out of prod.)

TO COUPLE ONLY WITH cylinder Kits 31 8884 - 3112099 / .T0 - 3115142 / .T0 - 3113030 --- WE SUGGEST TO USE bearings 6614105EA

TO COUPLE ONLY WITH cylinder Kits 31 8884 - 3112099.T0 - 3113030 - 3115142.T0 - 3115349 - 3115901 - (31 9128 - 3112099 - 3115142 : out of prod.) --- WE SUGGEST TO USE bearings 6614105EA

for vehicles WITH PRIMARY gear with coupling Ø 17

for vehicles WITH PRESSED fitting / coupling Ø 17 SECONDARY gear

TO COUPLE ONLY WITH cylinder Kits 3115385 - 3115883

for CYLINDERS Ø 47,6

TO COUPLE ONLY WITH cylinder Kits 3115142 - 3115142.T0 - 3115349 - 3115901

TYPE : C06100 - THE "TYPE" ONLY SPECIFIES THE MODEL IN WHICH HOMOLOGATION WAS VALIDATED , THIS DOES NOT LIMIT THE INSTALLATION

for ORIGINAL VALVE

ONLY for MHR C/RC-one CRANKCASE

ONLY for ORIGINAL CRANKCASE

Spare part for EXHAUST SYSTEM 3212115 : out of production

Can be rotated of 360°

Can be rotated of 360°

Can be rotated of 360° - for PHBG 15-21 Racing (linkage 28)

for ORIGINAL VARIATOR

for Multivar and original variator - rigidity increase compared to original spring: +114%

for Multivar and original variator - rigidity increase compared to original spring: +106%

for Multivar and original variator - rigidity increase compared to original spring: +60%

ELECTRIC STARTER IS CUT OUT

for Multivar and original variator - rigidity increase compared to original spring: +82%

for Multivar and original variator - rigidity increase compared to original spring: +30%

ONLY for OVER RANGE

ONLY FOR vehicles WITHOUT IMMOBILIZER KEY

ONLY FOR vehicles WITHOUT IMMOBILIZER KEY

Spare part for Malossi IGNITION 5511181 : out of production

Spare part for IGNITIONS 5514691 - 5515001 : out of production

ELECTRIC SYSTEM IS CUT OUT

IT CAN BE ASSEMBLED WITH NO MODIFICATION to the original system, EVEN ON vehicles PRODUCED 2001 --> - ONLY for vehicles WITHOUT IMMOBILIZER key

IT CAN BE ASSEMBLED WITH NO MODIFICATION to the original system, EVEN ON vehicles PRODUCED 2001 --> - ONLY for vehicles WITHOUT IMMOBILIZER key

ONLY for ORIGINAL CRANKCASE

Front - for vehicles PRODUCED 1996 --> ** HOMOLOGATED **

Rear - for vehicles PRODUCED 1996 -->

Front - for vehicles PRODUCED 1996 -->

Front - for vehicles PRODUCED 1996 -->

Front - for vehicles PRODUCED 1996 --> ** HOMOLOGATED **

Front - for vehicles PRODUCED 1996 -->

THE PAIR of shock-absorbers 46 9031 IS AVAILABLE ON SALE , TOO

THE PAIR of shock-absorbers 4614479 IS AVAILABLE ON SALE , TOO

THE PAIR of shock-absorbers 4614479 IS AVAILABLE ON SALE , TOO

Rigidy compared +20% to the Malossi shock abs. RS24/10

Rigidy compared -20% to the Malossi shock abs. RS24/10-R

Rigidy compared -30% to the Malossi shock abs. RS24/10-R

ONLY for vehicles WITH Malossi MHR C-one/RC-one ENGINE CRANKCASE (for PIAGGIO engine)

to be assembled EXCLUSIVELY with Malossi CARB.KITS: 1611021.T PHBG 19 BS, OR with 1613890.T0 PHBG 21 BS, OR with 1616276 VHST 28 BS

To be assembled EXCLUSIVELY with: CRANKSHAFTS (stroke 44 mm) 5317822 (5316029 : out of production) AND CYLINDER KIT 3115883

Carbonitrided inner ring , oversize balls and special reduced outer ring.

STRENGTHENED for ROAD and RACING USE

TO BE USE WITH MODULAR-HEAD cylinder kits

Spare part for EXHAUST SYSTEM 3212115 : out of production

Not suitable for original air box filter - ATTENTION: in order to use the MHR manifolds it is necessary to perform some small modifications to the adjacent plastic

Original spare Ø 20 : for original air box filter

For original air box filter

Not suitable for original air box filter

Not suitable for original air box filter - ATTENTION: in order to use the MHR manifolds it is necessary to perform some small modifications to the adjacent plastic

Not suitable for original air box filter - ATTENTION: in order to use the MHR manifolds it is necessary to perform some small modifications to the adjacent plastic

Can be rotated of 360°

Can be rotated of 360°

Can be rotated of 360° - for PHBG 15-21 Racing (linkage 28)

for ORIGINAL VALVE